| introduction | |
|
+4bud1970 heritage74 supersterl papagsi 8 posters |
Author | Message |
---|
papagsi Newbie
Posts : 27 Join date : 2010-05-07 Age : 39
| Subject: introduction Fri May 07, 2010 1:55 pm | |
| hi there neeb here not sure if this is the introduction section as im doing this on my phone . i was just wondering if anyone has had issues fitting hids as i will be attempting some tomorrow also my main issue is on idle every now and then the bus idle drops about 50 to 100 rpm it doesnt stall or effect the performance but its bloody anoying ive been told its the coil pack or the mass air flow changed both but no joy can any one help thanks . . paul | |
|
| |
supersterl Admin
Posts : 1354 Join date : 2009-11-24 Age : 67
| Subject: Re: introduction Fri May 07, 2010 8:06 pm | |
| Try do the pedal test and se if you can get any fault codes.. look in the "how to " section if your not sure how to do this.. | |
|
| |
heritage74 Event Manager
Posts : 286 Join date : 2010-03-01 Age : 49
| Subject: Re: introduction Fri May 07, 2010 8:13 pm | |
| hi mate and welcome to the site ive fitted hids to mine and everything was good just make sure you get the right ones as some which dont come with a resister will when fitted will flicker but other then that cant fault them mate | |
|
| |
papagsi Newbie
Posts : 27 Join date : 2010-05-07 Age : 39
| Subject: Re: introduction Fri May 07, 2010 9:38 pm | |
| hi there with the hids i got em from hids4u the pro kit so i hope they have the resistors how much buggering about was the adapting the original mounts to put the wires through ... and ta illl try the pedal test | |
|
| |
heritage74 Event Manager
Posts : 286 Join date : 2010-03-01 Age : 49
| Subject: Re: introduction Fri May 07, 2010 11:11 pm | |
| it aint to bad mate basically you got to cut all the inside off the bulb holder out and just thread the wires through make sure the bulb is a nice flush fit though other wise your lights will be out off line should take about an hour in all | |
|
| |
papagsi Newbie
Posts : 27 Join date : 2010-05-07 Age : 39
| Subject: Re: introduction Sat May 08, 2010 5:41 pm | |
| hids fitted cheers mate just gotta wait till its dark now lol | |
|
| |
supersterl Admin
Posts : 1354 Join date : 2009-11-24 Age : 67
| Subject: Re: introduction Sat May 08, 2010 6:58 pm | |
| let us know how they are when you try them in the dark.. | |
|
| |
papagsi Newbie
Posts : 27 Join date : 2010-05-07 Age : 39
| Subject: Re: introduction Mon May 10, 2010 3:52 pm | |
| hi guys do any of you have JUST lowering springs on your gsi models instead of coilovers im debating getting the eibach pro kit but not sure if it lowers the gsi buy much just wanna fill the arches abit but on a tight budget | |
|
| |
bud1970 Mod
Posts : 320 Join date : 2010-02-03 Age : 53
| Subject: Re: introduction Wed May 26, 2010 2:31 pm | |
| moved to the appropriate forum. hello and welcome to the site. | |
|
| |
andromeda411 Regional Co.
Posts : 334 Join date : 2010-03-25 Age : 54
| Subject: Re: introduction Wed May 26, 2010 4:31 pm | |
| | |
|
| |
Paz Admin
Posts : 489 Join date : 2010-01-31 Age : 55
| Subject: Re: introduction Wed May 26, 2010 8:41 pm | |
| | |
|
| |
clarky69 Member
Posts : 391 Join date : 2010-02-19 Age : 55
| Subject: Re: introduction Thu May 27, 2010 3:26 pm | |
| | |
|
| |
IAN74 Member
Posts : 663 Join date : 2010-02-24
| Subject: Re: introduction Thu May 27, 2010 9:54 pm | |
| hello and welcome to the site mate. | |
|
| |
Sponsored content
| Subject: Re: introduction | |
| |
|
| |
| introduction | |
|